Fortilink hardware switch. 1, the FortiOS switch controller now supports VLAN pruning.

• Fortilink hardware switch 0 Introduction FortiSwitch management Zero-touch management Zero-touch provisioning automation Configuring FortiLink Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network The FortiLink port(s) and interface type must match on the two FortiGate units. Create a trunk The FortiLink can consist of a single (physical) or multiple ports (802. If you wish both switches to be online, you need delete default fortilink interface, then create hardware switch with ports where you connect fortiswitches and in hardware switch settings via CLI make fortilink enabled. 5 (453) Authorized/Up 2 169. For example: config system proxy-arp. 1 Introduction FortiSwitch management Zero-touch management Configuring FortiLink Optional FortiLink Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network For this configuration, you create a FortiLink Split-Interface (an aggregate interface that contains one active link and one standby link). ; Click Create New. Managed FortiSwitch display. Fortinet recommends binding FortiLink on the hardware switch interface. set interface "V100" set ip 1. Bind FortiLink on hardware switch interface. set switch-controller-dynamic <FortiLink_policy_settings> next. FortiLink setup. 1, the FortiOS switch controller now supports VLAN pruning. This article describes how toconfigure manage FortiSwitches using hardware-switch interfaces and STP. ; Click inside the Interface members field. Some FortiSwitch models provide designated ports for the FortiLink connection, check the hardware manual to see which port is the designated FortiLink port. LAG is supported on all FortiSwitch models and on FortiGate models FGT This section provides information about how to set up and configure managed FortiSwitch units using the FortiGate unit (termed “using FortiSwitch in FortiLink mode”). Then FortiGate should become the CIST root all FortiLink hardware switch ports can be active at the same time, with traffic potentially only 1 "hop" away from FortiGate on their own uplink (no chain topology bottleneck). If your switches are not in MCLAG, then this is behavior by design with default fortilink interface, which is in aggregate mode. Select interfaces to add or remove them from the hardware switch, then click Close. 1 Introduction FortiSwitch management Zero-touch management Zero-touch provisioning automation Configuring FortiLink Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer The FortiLink can consist of a single (physical) or multiple ports (802. Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network The FortiLink port(s) and interface type must match on the two FortiGate units. edit <FortiLink_interface> set switch-controller-source-ip fixed. STP is a link-management protocol that ensures a loop-free layer HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink mode over a layer-3 network Switch redundancy with MCLAG The FortiLink ports and interface type must match on the two FortiGate units. delete port4 . next. 6. By Cloud. DHCP happens before Intra-VLAN traffic blocking is not supported when the FortiLink interface type is hardware switch or software switch. NOTE: Intra-VLAN traffic blocking is not supported when the FortiLink interface type is hardware switch or software switch. Fortigates 60D need at least two physical interfaces per Hardware switch. It's rather hard to grasp the concept of FMG but I think I'm getting there. After that the two physical interface of the hardware switch turned into independent physical interfaces. To log in from the FortiGate device to a switch managed by FortiLink with HTTPS: execute switch-controller ssh <FortiSwitch_user_name> <FortiSwitch_serial_number> For example: execute switch-controller ssh admin S524DF4K15000024 Each of these FortiLink ports is added to the logical hardware-switch or software-switch interface on the FortiGate unit. NOTE: STP and STP forwarding are both supported by the FortiLink hardware-switch interface. If the default FortiLink interface was removed, on the FortiGate GUI, edit the interface and select Dedicated to FortiSwitch . HA-mode FortiGate units in remote sites. If the FortiGate model does not support aggregate interfaces, you need to configure the FortiGate unit to be the Common and Internal Spanning Tree (CIST) by assigning the lowest STP priority to the FortiGate unit and placing each switch in a To use the FortiLink interface as the source IP address: config system interface. You can create a PortChannel with no address info but you can't join it to a hardware switch. By Solution. The benefit of using hardware switch instead of link aggregate to manage switches is that in an HA active-passive cluster, the FortiSwitches can be connected in a cascading manner without MC-LAG config. 1. set fortilink-p2p-tpid <0x0001-0xfffe> end FortiLink Guide Whatʼs new in FortiOS 7. Connect the FortiSwitch: Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network For this configuration, you create a FortiLink Split-Interface (an aggregate interface that contains one active link and one standby link). fortinet. Configure the It would also work if you made a “hard-switch” type FortiLink and attached both switches to both FortiGates (in an “x” pattern). 4, MCLAG was not supported when access rings were present. ; Set VLAN ID to 100. ; Set Role to LAN. not automatically loop-tolerant (you have to fiddle with STP The hardware switch interface can be seen in the image below named "lan". However, if for example you need two distribution switches to directly connect via FortiLink and both be active, it might be better to use the Hardware Switch FortiLink. The only thing I found odd is that I read up on multiple articles to set this up, and I matched them; very little if anything was said about the Fortilink setup. Before connecting the FortiSwitch and FortiGate units, ensure that the switch controller feature is enabled on the FortiGate unit with the FortiGate GUI or CLI to enable the switch controller. Power on the FortiSwitch device. not automatically loop-tolerant (you have to fiddle with STP (Optional) If the FortiLink physical ports are currently included in the internal interface, edit the internal interface, and remove the desired ports from the Physical Interface Members. FGT_Switch_Controller (fol3_wan) # set switch-controller-source-ip fixed. Go I finally deleted "internal" hardware Switch. When intra-VLAN traffic blocking is enabled, to allow traffic between hosts, you need to configure the proxy ARP with the config system proxy-arp CLI command and configure a firewall policy. com/document/fortiswitch/7. Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network Previously, the default method was “FortiLink” (set fortilink-neighbor-detect fortilink). Go HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink mode over a layer-3 network Managing FortiSwitch units on VXLAN interfaces diagnose switch fortilink-auth statistics <port_name> To delete the FortiLink authentication traffic statistics for the port from the FortiSwitch unit: Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network The S-VLAN must be configured on the same VDOM where the FortiLink interface is; for example, if the FortiLink interface is on the root VDOM, all S-VLANs Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink Guide Whatʼs new in FortiOS 7. Solution. Assign all ports to vsw. set vlanid 99 next end config switch-controller global set default-virtual-switch-vlan "bbb-vlan99" end. 1 Introduction FortiSwitch management Zero-touch management Zero-touch provisioning automation Configuring FortiLink Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network For this configuration, you create a FortiLink Split-Interface (an aggregate interface that contains one active link and one standby link). Create the FortiLink policy settings Using the GUI. To configure a FortiSwitch unit to operate in a layer-3 network: NOTE: You must enter these commands in the indicated order for this feature to work. ; In the Name field, enter a name for the NAC policy. Then I cabled the 30E Internal to port 2 on that switch. 2 that allows for multiple FortiLink interfaces in the GUI! Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink For this, FortiGate should be the lowest priority and each switch should be in a different region. all FortiLink hardware switch ports can be active at the same time, with traffic potentially only 1 "hop" away from FortiGate on their own uplink (no chain topology bottleneck). Internal is a HW switch of port 1-4. 4/devices-managed-by You can configure FortiLink on a logical interface: link-aggregation group (LAG), hardware switch, or software switch. To log in from the FortiGate device to a switch managed by FortiLink with HTTPS: execute switch-controller ssh <FortiSwitch_user_name> <FortiSwitch_serial_number> For example: execute switch-controller ssh admin S524DF4K15000024 FortiLink: Hardware Switch: Basically I need to make connection between new network on FortiSwitches connected with Fortilink to FortiGates and old network on different vendor switches there. Scope: All FortiOS. 4, MCLAG is supported, even with access rings present. 1q VLAN tagging, will have Layer 2 connectivity with the FortiSwitch ports. delete port5. The available options depend on the FortiGate model. 5 Introduction FortiSwitch management Zero-touch management Zero-touch provisioning automation Configuring FortiLink Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer STP and STP forwarding are both supported by the FortiLink hardware-switch interface. VLAN pruning prevents unnecessary traffic from unused VLANs by only allowing traffic from the VLANs required for the inter-switch link (ISL) trunks. These devices, which FortiLink Guide Whatʼs new in FortiOS 7. Check the FortiGate feature You can configure FortiLink on a logical interface: link-aggregation group (LAG), hardware switch, or software switch). NOTE: Before FortiSwitchOS 3. config You can configure FortiLink on a logical interface: link-aggregation group (LAG), hardware switch, or software switch. 0 (5029) Authorized/Up V 1. Each of these FortiLink ports is added to the logical hardware-switch or software-switch interface on the FortiGate unit. 5 HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink mode over a layer-3 network edit <FortiLink_interface> set switch-controller-source-ip fixed. 1 Introduction FortiSwitch management Zero-touch management Zero-touch provisioning automation Configuring FortiLink Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer FortiLink Guide Whatʼs new in FortiOS 7. I created a VLAN 130 inside FortiLink on Gate and added untagged to 130 on port 2 on one switch. For more details, see Zero-touch provisioning automation. Intra-VLAN traffic blocking is not supported when the FortiLink interface type is hardware switch or software switch. To view the interface via the CLI: # show system interface lan Use the steps provided below to completely remove the switch interface. Reply reply Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink mode over a layer-3 network Refer to the FortiSwitchOS feature matrix for details about the FortiLink features supported by each FortiSwitch model. 2 Introduction FortiSwitch management Zero-touch management Configuring FortiLink Optional FortiLink The FortiLink can consist of a single (physical) or multiple ports (802. Creating VLANs To create VLANs in the switch controller: Go to WiFi & Switch Controller > FortiSwitch VLANs, and click Create New. Go to See more This example provides a recommended configuration of FortiLink where multiple FortiSwitches are managed by an A-P mode HA cluster of FortiGates as switch controller via This article describes how to use the hardware switch to manage the FortiSwitches. 0: On the HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink mode over a layer-3 network Managing FortiSwitch units on VXLAN interfaces FortiLink and SNMP must be configured on the FortiGate device. Enable FortiLink on that interface via CLI FortiLink Guide Whatʼs new in FortiOS 7. Thanks STP and STP forwarding are both supported by the FortiLink hardware-switch interface. Hardware switch topology: HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink mode over a layer-3 network When you interconnect FortiLink fabrics, each FortiGate device manages its own FortiSwitch units. 0 Introduction FortiSwitch management Zero-touch management Zero-touch provisioning automation HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink mode over a layer-3 network HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink mode over a layer-3 network Switch redundancy with MCLAG STP is enabled by default for the non-FortiLink ports on the managed FortiSwitch units. This would eliminate the switch attached to the active FortiGate from being a single point of failure taking both switches (and all 3 internet links) down if the tier 1 switch fails. https://docs. Each upstreams a FS108E-POE from port 8. When deploying a new fortigate (especially the small ones) they come with the default virtual-switch FortiLink Guide Whatʼs new in FortiOS 7. Connecting FortiLink ports to switch ports To connect FortiLink ports: Remove the FortiSwitch from the box, and deploy it, whether mounting it in a rack or otherwise. config switch global. FortiLink Guide Whatʼs new in FortiOS 7. FortiLink is not supported in transparent mode. LAG is supported on all FortiSwitch models. This might help with what you want to do: Bind FortiLink on hardware switch interface. This interval cannot be changed. To add an interface to a hardware switch, it cannot be referenced by an existing configuration and its IP address must be set to Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network In FortiSwitchOS 3. It is enabled by default. To configure a FortiSwitch unit to operate in a layer-3 network: FortiLink Guide Whatʼs new in FortiOS 7. The mcast-snooping-flood-traffic and igmp-snooping-flood-reports settings must be disabled on the ISL and FortiLink trunks; but the mcast-snooping-flood-traffic and igmp-snooping-flood-reports settings must be STP and STP forwarding are both supported by the FortiLink hardware-switch interface. If an authorized FortiSwitch is always offline, go to the FortiGate CLI To change the ports in a hardware switch in the GUI: Go to Network > Interface and edit the hardware switch. Port1&2 on FG100 are in Hardware Switch mode? This is the only mode that works with your topology. 3. Go to WiFi & Switch Controller > Managed FortiSwitch to see all of the switches being managed by your FortiGate. Starting with FortiSwitchOS 3. 0 Introduction FortiSwitch management Zero-touch management Zero-touch provisioning automation Configuring FortiLink Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer Setup a Hardware switch. set vlanid 99 next end config switch-controller global set default-virtual-switch-vlan Make a hardware switch that has all physical FortiGate ports Set the hardware switch to FortiLink. If an authorized FortiSwitch is always offline, go to the FortiGate CLI Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink mode over a layer-3 network Refer to the FortiSwitchOS feature matrix for details about the FortiLink features supported by each FortiSwitch model. 2 Introduction FortiSwitch management Zero-touch management Configuring FortiLink Optional FortiLink FortiLink Guide Whatʼs new in FortiOS 7. Since the hardware switch interface can leverage hardware chips to forward traffic, it does not consume CPU capacity, unlike a software switch. 254. The FortiLink fabric interconnection points are seen as access ports from each FortiGate unit; no inter-switch links are formed. The firewall policy which is linked to the "lan" interface must first be deleted. If the FortiGate model does not support aggregate interfaces, you need to configure the FortiGate unit to be the Common and Internal Spanning Tree (CIST) by assigning the lowest STP priority to the FortiGate unit and placing each switch in a STP and STP forwarding are both supported by the FortiLink hardware-switch interface. 1 with FortiSwitchOS 7. 0 and later releases, you can use any of the switch ports for FortiLink. end. You can chose to connect a single FortiLink port or multiple FortiLink ports as a logical interface (link-aggregation group, hardware switch, or 7) After the reboot, it should be seen the topology created with the Hardware switch. 1. Doing this will have the switches communicate the link awareness between themselves (paraphrasing here). These devices, which must support IEEE 802. If the FortiGate model does not support aggregate interfaces, you need to configure the FortiGate unit to be the Common and Internal Spanning Tree (CIST) by assigning the lowest STP priority to the FortiGate unit and placing each switch in a Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink Guide Whatʼs new in FortiOS 7. 6 Introduction Special notices FortiSwitch management Zero-touch management Configuring FortiLink Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network set switch-fortilink "fortilink" set switch-group "Office1switches" set switch-mac-policy "Office1_PC" set firewall-address "office1_device" next. If the FortiGate model does not support aggregate interfaces, you need to configure the FortiGate unit to be the Common and Internal Spanning Tree (CIST) by assigning the lowest STP priority to the FortiGate unit and placing each switch in a In FortiSwitchOS 3. 4 Introduction FortiSwitch management Zero-touch management Zero-touch provisioning automation Configuring FortiLink Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink mode over a layer-3 network Switch redundancy with MCLAG set interface "flink-lag" // this is the FortiLink interface in the root VDOM. By automatically creating FortiLink interfaces as a logical aggregate or hard/soft Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network (termed “using FortiSwitch in FortiLink mode”). set fsw-wan1-admin enable. You can chose to connect a single FortiLink port or multiple FortiLink ports as a logical interface (link-aggregation group, hardware switch, or Bind FortiLink on hardware switch interface. VoIP phones from new network need to connect with server on with VoIP central that is located with old network. 4 HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink mode over a layer-3 network Managing FortiSwitch units on VXLAN interfaces diagnose switch fortilink-auth statistics <port_name> To delete the FortiLink authentication traffic statistics for the port from the FortiSwitch unit: STP and STP forwarding are both supported by the FortiLink hardware-switch interface. . One thing that I can't seem to get working or understand. In the Interface members field, click + and select the interface(s) you want to designate as FortiLink interface members. I used these for the policies. ; If you want the STP and STP forwarding are both supported by the FortiLink hardware-switch interface. To do Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP; FortiLink over a point-to-point layer-2 network; FortiLink mode over a layer-3 network; Managing FortiSwitch units on VXLAN interfaces; Switch redundancy with MCLAG Ok, I performed a factory reset on my FGT-60E running 6. 3ad type (Aggregate). set rate <rate> FortiLink Guide Whatʼs new in FortiOS 7. 2 GA and it created a default "fortilink" interface as 802. The FS-6xxF models now support the same LAN-segment functionality as the 200 Series and FortiLink Guide Whatʼs new in FortiOS 7. Go to WiFI & Switch Controller > FortiLink Interface to create or edit FortiLink interfaces. If the FortiGate model does not support aggregate interfaces, you need to configure the FortiGate unit to be the Common and Internal Spanning Tree (CIST) by assigning the lowest STP priority to the FortiGate unit and placing each switch in a The FortiLink can consist of a single (physical) or multiple ports (802. 2. Depending on the FortiGate model and software release, this feature might be enabled by default. The switch supports up to 1,023 user Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink interface : flink SWITCH-ID VERSION STATUS FLAG ADDRESS JOIN-TIME SERIAL FS1D243Z17000032 v7. NOTE: Using the GUI to configure a NAC policy and a dynamic firewall address: Go to WiFi & Switch Controller > NAC Policies. Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network STP is enabled by default for the non-FortiLink ports on the managed FortiSwitch units. The switch supports up to 1,023 user In FortiSwitchOS 3. ; In the IP/Netmask box, enter a subnet for your POS. Each switch has a AP321C on port 1. config system virtual-switch edit "FortiLink" set physical-switch "sw0" config port edit "internal1" next edit "internal2" next end next end. 4. To configure a FortiSwitch unit to operate in a layer-3 network: NOTE: You must enter these commands in the indicated order for this Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network In FortiSwitchOS 3. edit lan. Another alternative, depending on your hardware, you can consider is using a VLAN Switch. This is done since FortiOS cannot FortiLink Guide Whatʼs new in FortiOS 7. 0. In the following procedure, port 4 and port 5 are configured as a FortiLink LAG. 1 Introduction FortiSwitch management Zero-touch management Zero-touch provisioning automation Configuring FortiLink Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network (termed “using FortiSwitch in FortiLink mode”). VLAN pruning. So, it is necessary to move a switch to another region by setting the revision. Enter a name Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink Guide Whatʼs new in FortiOS 7. If required, remove the FortiLink ports from the lan interface: config system virtual-switch. 0, when using HA-mode FortiGate units to manage STP and STP forwarding are both supported by the FortiLink hardware-switch interface. NOTE: HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink mode over a layer-3 network edit <FortiLink_interface> set switch-controller-source-ip fixed. Summary. ; Set the following options to create a VLAN for POS: Set Interface Name to POS. 0, when using HA-mode FortiGate units to manage Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink mode over a layer-3 network Managing FortiSwitch units on VXLAN interfaces set fsw-wan1-peer fortilink. Some or all of the switch ports (depending on the model) support auto-discovery of the FortiLink ports. You can chose to Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) FortiLink interface : flink SWITCH-ID VERSION STATUS FLAG ADDRESS JOIN-TIME SERIAL FS1D243Z17000032 v7. The easiest way I was able to create a FortiLink interface tied to a Hardware switch was leverage a new feature in 6. Solution: Enable the FortiLink option from the CLI. Select Topology from the drop-down menu in the upper right corner to see which devices are connected. In FortiLink Guide Whatʼs new in FortiOS 7. ; Make certain that the status is set to Enabled. 5 Introduction FortiSwitch management Zero-touch management Zero-touch provisioning automation Configuring FortiLink Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer Go to WiFi and Switch Controller > FortiLink Interface. NOTE: FortiLink is not You can configure the FortiLink as a logical interface: link-aggregation group (LAG), hardware switch, or software switch). 0 Introduction FortiSwitch management Zero-touch management Zero-touch provisioning automation Configuring FortiLink Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer Inside LAN is mapped to the hardware switch interface. 1 Introduction FortiSwitch management Zero-touch management Configuring FortiLink Optional FortiLink Starting in FortOS 6. STP is a link-management protocol that ensures a loop-free layer-2 network In FortiSwitchOS 3. The New Interface pane is displayed. Go to: System > Network > Interfaces . edit 1. 3ad aggregate, hardware switch, or software switch). 3, you can now configure a FortiLink-over-layer-3 network to use the FortiLink interface as the source IP address for the communication between the FortiGate unit and the FortiSwitch unit. Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network edit fortilink. When using an aggregate interface for the active/standby FortiLink configuration, make sure the FortiLink split Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink interface : vx100 SWITCH-ID VERSION STATUS FLAG ADDRESS JOIN-TIME SERIAL S108DV3A17000071 v7. x (and later). You can chose to connect a single FortiLink port or multiple FortiLink ports as a logical interface (link-aggregation group, hardware switch, or Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network For this configuration, you create a FortiLink Split-Interface (an aggregate interface that contains one active link and one standby link). 1 Introduction FortiSwitch management Zero-touch management Zero-touch provisioning automation Configuring FortiLink Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer Intra-VLAN traffic blocking is not supported when the FortiLink interface type is hardware switch or software switch. By default, it is 0x8100. In this example Bind FortiLink on hardware switch interface. If the FortiGate model does not support aggregate interfaces, you need to configure the FortiGate unit to be the Common and Internal Spanning Tree (CIST) by assigning the lowest STP priority to the FortiGate unit and placing each switch in a Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network Using FortiLink mode over a layer-3 network requires both FortiOS 7. If the FortiGate model does not support aggregate interfaces, you need to configure the FortiGate unit to be the Common and Internal Spanning Tree (CIST) by assigning the lowest STP priority to the FortiGate unit and placing each switch in a Enable the FortiLink point-to-point network on each FortiSwitch unit: config switch physical-port. As displayed, more FortiLink interfaces have been created, fortilink1 was dedicated to an aggregate interface. 4 Introduction Special notices FortiSwitch management Zero-touch management Configuring FortiLink Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network set interface "flink-lag" // this is the FortiLink interface in the root VDOM. NOTE: If you are going to use IGMP snooping with an MCLAG topology: On the global switch level, mclag-igmpsnooping-aware must be enabled. Authorized FortiSwitch always offline. ; Select Device for the category. When the FortiLink is established successfully, the status is green (next to the FortiGate interface name and on the FortiSwitch The FortiLink can consist of a single (physical) or multiple ports (802. If the FortiGate model does not support aggregate interfaces, you need to configure the FortiGate unit to be the Common and Internal Spanning Tree (CIST) by assigning the lowest STP priority to the FortiGate unit and placing each switch in a Spanning Tree Protocol (STP) and STP forwarding are both supported by the FortiLink hardware-switch interface. You an create a software switch, however, and join it all together that way. 4 61E Gate has two physical interfaces in a hardware switch dedicated to FortiLink. STP and STP forwarding are both supported by the FortiLink hardware-switch interface. NOTE: Before FortiOS 6. If an authorized FortiSwitch is always offline, go to the FortiGate CLI Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink Guide Whatʼs new in FortiOS 7. With this release, the default neighbor-detection method is now Intra-VLAN traffic blocking is not supported when the FortiLink interface type is hardware switch or software switch. config port. Go back to the root Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink Guide Whatʼs new in FortiOS 7. You can chose to connect a single FortiLink port or multiple FortiLink ports as a logical interface (link-aggregation group, hardware switch, or FGT(Hardware_Switch) # end The difference will be visible, once the option has been enabled through the CLI. Before FortiOS 7. 2 Introduction FortiSwitch management Zero-touch management Configuring FortiLink Optional FortiLink configuration required before discovering and authorizing FortiSwitch units HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink mode over a layer-3 network In addition to connecting Fortilink A/B ports to each switch, you must connect the switches to ea. ; Set Color to Red. The maximum number of supported FortiSwitch units depends For the FortiLink connection to each distribution switch, you create a FortiLink split interface (an aggregate interface that contains one active link and one standby link). Note that spanning tree will take one of the links down to avoid a loop in this case HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink mode over a layer-3 network To configure storm control for all switch ports (including both FortiLink ports and non-FortiLink ports) on the managed switches, use the following FortiOS CLI commands: config switch-controller storm-control. 1 Introduction FortiSwitch management Zero-touch management Configuring FortiLink Optional FortiLink The FortiLink can consist of a single (physical) or multiple ports (802. For FortiGate models lower than 100, you can use the default fortilink hardware switch or software switch interface and then add ports. x (and later) and FortiSwitchOS 7. Products Best Practices Hardware Guides Products A-Z. FortiLink is supported on all Ethernet ports except HA and MGMT. I will have to check tomorrow, but that may save me some of the work. NOTE: LAG is supported on all FortiSwitch models and on FortiGate models FGT-100D and above. Optionally, you can connect other devices to the FortiGate logical interface. 1 Introduction FortiSwitch management Zero-touch management Zero-touch provisioning automation HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink mode over a layer-3 network Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network The FortiLink port(s) and interface type must match on the two FortiGate units. Starting in FortiOS 7. 5 Introduction FortiSwitch management Zero-touch management Zero-touch provisioning automation Configuring FortiLink Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer The FortiLink can consist of a single (physical) or multiple ports (802. other, otherwise it will never, ever work. If an authorized FortiSwitch is always offline, go to the FortiGate CLI In FortiSwitchOS 3. One could do this via the GUI as well. single switch/link failure should only affect that one switch; Cons: no link-level redundancy per switch. LAG is supported on all FortiSwitch models and on FortiGate models FGT-100D and above. In FortiSwitchOS 3. There are two sites in You can configure FortiLink on a logical interface: link-aggregation group (LAG), hardware switch, or software switch). How is best to achieve this: Create new VLAN on Each of these FortiLink ports is added to the logical hardware-switch or software-switch interface on the FortiGate unit. no virtual stacking. 0 Introduction FortiSwitch management Zero-touch management Zero-touch provisioning automation Configuring FortiLink Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer FortiManager Interface Configuration / Removing Hardware Switch and FortiLink . You can still use the FortiLink Guide Whatʼs new in FortiOS 7. The software-switch interface is not supported. FortiSwitch units update the CPU and memory statistics every 30 seconds. edit <port_name> set fortilink-p2p enable. HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink mode over a layer-3 network A switch was connected using FortiLink mode over a layer-2 or layer-3 network. In-band management. 0 and later releases, the FortiSwitch supports untagged and tagged frames in FortiLink mode. FortiLink For the AP, create a Bridged SSID on the FortiLink VLAN. Secure Networking Unified SASE Security Operations Secure SD-WAN Secure Access Service Edge (SASE) FGT_Switch_Controller (fol3_wan) # set fortilink enable. ; Click Specify to select which FortiSwitch groups to apply the NAC policy to or click All. Connect the FortiSwitch to the FortiGate by using two Ethernet connections. Hey guys, we're starting to leverage FMG for new deployments. By 4D Pillars. The maximum number of supported FortiSwitch units depends Single FortiGate unit managing multiple FortiSwitch units (using a hardware or software switch interface) HA-mode FortiGate units using hardware-switch interfaces and STP FortiLink over a point-to-point layer-2 network FortiLink mode over a layer-3 network Refer to the FortiSwitchOS feature matrix for details about the FortiLink features supported by each FortiSwitch model. Make certain that the FortiLink point-to-point TPID value is the same on each FortiSwitch unit. The FortiGate is a router, not a switch. Select Create New > Interface.